Rice-lake 880 Performance Series Indicator/Controller Techni Manual de usuario Pagina 102
- Pagina / 120
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
96 880 Technical/Service Manual
10.4 Status Messages
The EDP command P can be used to provide status about the indicator.
•The
P EDP command returns whatever is currently shown in the indicator’s primary display area.
PPPPPPP uu
where:
•
PPPPPPP is the information shown on the primary display
•
uu is the 2-digit units annunciator
If the indicator is in an underrange or
overload condition, the weight value is replaced with &&&&&& (overload) or
:::::: (underrange).
10.5 TARE and ZERO Key Functions
The function of the front panel TARE and ZERO keys depend on the value specified for the REGULA parameter
in the FEATUR menu, see Figure 3-11 on page 37.
Table 9-4 describes the function of these k
eys for each of the regulatory modes.
REGULAT
Parameter
Value
Weight on
Scale
Tare i n
System
Front Panel TARE Key or KTARE command
(TAREFN – tare function setting)
Front panel ZERO key
or KZERO command
KEYED PBONLY BOTH
NTEP zero or
n
egative
No Keyed prompt (1) No Action Keyed prompt (1) Zero
Yes Keyed prompt (2) Clear tare Keyed prompt (2) Zero
positive No Keyed prompt (1) Tare Tare Zero
Yes Keyed prompt (2) Tare Tare
Zero
CANADA zero or
negative
No Keyed prompt (1) No Action Keyed prompt (1) Zero
Yes Keyed prompt (2) Clear tare Keyed prompt (2) Zero
positive No No Action Tare Ta re Zero
Yes No Action No Action No Action Zero
OIML zero or
n
egative
No Keyed prompt (1) No Action Keyed prompt (1) Zero
Yes Keyed prompt (2) Clear tare Keyed prompt (2) Zero and clear Tare (3)
positive No Keyed prompt (1) Tare Tare Zero
Yes Keyed prompt (2) Tare Tare
Zero and clear Tare (3)
NONE zero or
negative
No Keyed prompt (1) Tare Keyed prompt (1) Zero
Yes Keyed prompt (2) Clear tare Keyed prompt (2) Zero
positive No Keyed prompt (1) Tare Tare Zero
Yes Keyed prompt (2) Clear tare Clear tare Zero
Note
1. Entering a Zero tare will CANCEL the entry. Any other value will be accepted as a Keyed Tare.
2. Entering a Zero tare will CLEAR the current Tare. Any other
value will be accepted as a Keyed Tare.
3. The indicator will Zero and Clear the Tare only is the gross weight i
f within ZRANGE. No action is taken if the weight is outside
of ZRANGE
Table 10-4. TARE and ZERO Key Functions for REGULA Parameter Settings
- 880 Performance Series 1
- Technical/Service 1
- Contents 3
- About This Manual 7
- 1.0 Introduction 7
- General Safety 8
- 1.2 Operating Modes 9
- 1.3 Front Panel Display 9
- Center of Zero LED 10
- Standstill LED 10
- 1.4 Indicator Operations 11
- 1.4.7 Print Ticket 12
- 1.4.8 Front Panel Setup 12
- 1.4.10 Setpoints 13
- Turn Setpoint On or Off 13
- 1.4.11 Set Time and Date 14
- 1.4.12 Display Accumulator 14
- 1.4.13 Clear the Accumulator 14
- 1.4.14 Display Tare 15
- 2.0 Installation 16
- 2.2 Panel Mount Installation 17
- Important 18
- J1 J2 J3 J4 J5 J6 19
- 2.4 Display Board Replacement 22
- 2.5 Cable Connections 22
- 2.6 USB Host 24
- 2.7 Ethernet Communications 24
- 2.8 CPU Board 25
- 2.10 Board Replacement 26
- 2.11 Digital I/O 28
- 2.12 Legal for Trade Sealing 28
- 2.13 Option Cards 29
- 2.14 Battery Replacement 29
- 2.15 Replacement Parts 30
- 3.1.3 User Setup Menu 33
- 0 0 0 0 0 0 34
- 3.2.1 Audit Menu 35
- 3.2.2 Setup Menu 36
- 37
- SCALE Menu 38
- 3.2.4 FORMAT Menu 40
- FORMAT Menu 41
- 3.2.5 Calibration Menu 42
- FEATUR Menu 44
- COM Menu 50
- ETHERNET Menu 52
- 3.2.11 USB Host 53
- 3.2.12 Print Format Menu 54
- Configuration 51 57
- SETPTS Menu 58
- 4.0 Calibration 63
- 4.1 Front Panel Calibration 64
- 4.1.2 Rezero 65
- 4.5 Gravity Compensation 66
- 4.6 EDP Command Calibration 67
- 4.7 Revolution 67
- Calibration 67
- 5.0 Using Revolution 68
- 5.2 Configuration 69
- 5.4 Revolution Help 70
- 6.0 EDP Commands 71
- 6.1.2 Reporting Commands 72
- Scales Menu 73
- Format Menu 73
- Calibration Menu 74
- Ports COM Menu 74
- Ports – Field Bus Menu 75
- Ports – Ethernet Menu 75
- Ports – USBCOM Menu 76
- Stream Tokens Menu 76
- Feature Menu 76
- Regulatory Menu 77
- Time and Date 77
- Passwords Menu 77
- Keypad Lock Menu 77
- Setpoints Menu 78
- Print Format Menu 80
- Analog Out Menu 80
- 6.1.5 Normal Mode Commands 81
- Digital I/O Control Menu 82
- 6.1.6 ERROR Commands Output 82
- 7.0 Print Formatting 83
- 7.2 Default Print Formats 84
- 7.3 Customizing Print Formats 85
- 7.3.3 Using Revolution 86
- 8.0 Setpoints 87
- 8.2 Batch Operations 89
- 8.3 Batching Examples 91
- Example 2 92
- 9.0 Ethernet and USB 93
- Ethernet and USB 89 95
- Using Revolution 96
- with Ethernet 96
- 9.2 USB Host 97
- 9.2.2 USB Memory storage 98
- Saving Configuration 98
- Loading Configuration 98
- 10.0 Appendix 100
- 10.3 ERROR Commands Output 101
- 10.4 Status Messages 102
- 10.6 Data Formats 103
- <STX> 104
- ONTROL-B>AXG#1<CR> 105
- 10.8.1 Toledo 8142 Indicator 108
- 10.8.2 Cardinal 738 Indicator 109
- 10.9 ASCII Character Chart 111
- 10.10 Digital Filtering 113
- (Section 4.0) 114
- 10.12 Specifications 115
- 880 Limited Warranty 116
- For More Information 117
- PN 158387 Rev C 120
Relacionado con productos y manuales para Escamas Rice-lake 880 Performance Series Indicator/Controller Techni
(4 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales