Rice-lake 880 Performance Series Indicator/Controller Techni Manual de usuario Pagina 61
- Pagina / 120
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Configuration 55
3.2.15 Analog Output Menu
The ALGOUT menu is used only if the analog output option is installed. If the analog output option is installed,
configure all other indicator functions and calibrate the indicator before configuring the analog output. See
Section 10.11 on page 108 for analog output calibration procedures.
SETUP
........
....
ALGOUT
....
number
TWSPAN
OFF
ON
MAXNEGMINNEG
OFF
ON
ERRACT
FULLSC
ZEROSC
HOLD
OUTPUT
0-10V
0-20MA
4-20MA
MODE
GROSS
NET
MAX
10000
number
TWZERO
number
MIN
number
0
Figure 3-23. Analog Output Menu
Table 3-17. Analog Output Menu Parameters
ALG OUT Menu
Parameter Choices Description
Level 2 submenus
MODE GROSS
NET
Defines if the output follows the
GROSS or NET weight.
OUTPUT 0-10V
0-20MA
4-20MA
Selects whether the analog output supplies voltage (0–10
V), current (0-20mA),
or current (4-20mA).
ERRACT FULLSC
HOLD
ZEROSC
Error action. Specifies how the analog output
responds to system error conditions.
Possible values are:
FULLSC: Set to full value (10 V or 2
0 mA, depending on output setting)
HOLD: Hold current value
ZEROSC: Set to zero value (0 V or 4 mA, depending on output setting)
MIN 0.000000
number
Specifies the minimum weight value tracked by the
analog output. Specify a value in the range
0–999999.
MIN NEG OFF
ON
Set to ON if the MIN value is negative.
MAX 10000.00
number
Specifies the maximum weight value tracked by the analog output. Speci
fy a value in the range
0–999999.
MAX NEG OFF
ON
Set to ON if the MAX value is negative.
TWZERO 000000
number
Calibrate zero. Adjust the analog output zero calibration. See Section 10.11 on page 108.
TWSPAN 000000
number
Calibrate span. Adjust the analog
output span calibration. See Section 10.11 on page 108
- 880 Performance Series 1
- Technical/Service 1
- Contents 3
- About This Manual 7
- 1.0 Introduction 7
- General Safety 8
- 1.2 Operating Modes 9
- 1.3 Front Panel Display 9
- Center of Zero LED 10
- Standstill LED 10
- 1.4 Indicator Operations 11
- 1.4.7 Print Ticket 12
- 1.4.8 Front Panel Setup 12
- 1.4.10 Setpoints 13
- Turn Setpoint On or Off 13
- 1.4.11 Set Time and Date 14
- 1.4.12 Display Accumulator 14
- 1.4.13 Clear the Accumulator 14
- 1.4.14 Display Tare 15
- 2.0 Installation 16
- 2.2 Panel Mount Installation 17
- Important 18
- J1 J2 J3 J4 J5 J6 19
- 2.4 Display Board Replacement 22
- 2.5 Cable Connections 22
- 2.6 USB Host 24
- 2.7 Ethernet Communications 24
- 2.8 CPU Board 25
- 2.10 Board Replacement 26
- 2.11 Digital I/O 28
- 2.12 Legal for Trade Sealing 28
- 2.13 Option Cards 29
- 2.14 Battery Replacement 29
- 2.15 Replacement Parts 30
- 3.1.3 User Setup Menu 33
- 0 0 0 0 0 0 34
- 3.2.1 Audit Menu 35
- 3.2.2 Setup Menu 36
- 37
- SCALE Menu 38
- 3.2.4 FORMAT Menu 40
- FORMAT Menu 41
- 3.2.5 Calibration Menu 42
- FEATUR Menu 44
- COM Menu 50
- ETHERNET Menu 52
- 3.2.11 USB Host 53
- 3.2.12 Print Format Menu 54
- Configuration 51 57
- SETPTS Menu 58
- 4.0 Calibration 63
- 4.1 Front Panel Calibration 64
- 4.1.2 Rezero 65
- 4.5 Gravity Compensation 66
- 4.6 EDP Command Calibration 67
- 4.7 Revolution 67
- Calibration 67
- 5.0 Using Revolution 68
- 5.2 Configuration 69
- 5.4 Revolution Help 70
- 6.0 EDP Commands 71
- 6.1.2 Reporting Commands 72
- Scales Menu 73
- Format Menu 73
- Calibration Menu 74
- Ports COM Menu 74
- Ports – Field Bus Menu 75
- Ports – Ethernet Menu 75
- Ports – USBCOM Menu 76
- Stream Tokens Menu 76
- Feature Menu 76
- Regulatory Menu 77
- Time and Date 77
- Passwords Menu 77
- Keypad Lock Menu 77
- Setpoints Menu 78
- Print Format Menu 80
- Analog Out Menu 80
- 6.1.5 Normal Mode Commands 81
- Digital I/O Control Menu 82
- 6.1.6 ERROR Commands Output 82
- 7.0 Print Formatting 83
- 7.2 Default Print Formats 84
- 7.3 Customizing Print Formats 85
- 7.3.3 Using Revolution 86
- 8.0 Setpoints 87
- 8.2 Batch Operations 89
- 8.3 Batching Examples 91
- Example 2 92
- 9.0 Ethernet and USB 93
- Ethernet and USB 89 95
- Using Revolution 96
- with Ethernet 96
- 9.2 USB Host 97
- 9.2.2 USB Memory storage 98
- Saving Configuration 98
- Loading Configuration 98
- 10.0 Appendix 100
- 10.3 ERROR Commands Output 101
- 10.4 Status Messages 102
- 10.6 Data Formats 103
- <STX> 104
- ONTROL-B>AXG#1<CR> 105
- 10.8.1 Toledo 8142 Indicator 108
- 10.8.2 Cardinal 738 Indicator 109
- 10.9 ASCII Character Chart 111
- 10.10 Digital Filtering 113
- (Section 4.0) 114
- 10.12 Specifications 115
- 880 Limited Warranty 116
- For More Information 117
- PN 158387 Rev C 120
Relacionado con productos y manuales para Escamas Rice-lake 880 Performance Series Indicator/Controller Techni
(4 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.089 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales