Rice-lake 880 Performance Series Indicator/Controller Techni Manual de usuario Pagina 13
- Pagina / 120
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Introduction 7
1.4.10 Setpoints
Setpoints must be enabled in the setup mode to be accessible in the user setup mode.
To enter the setup mode:
1. Remove the large fillister head screw from the
back of the enclosure.
2. Insert a non-conductive tool into
the access hole and press the setup switch. Indicator display changes to
show SCALE.
3. Press
or until SETPTS is displayed.
4. Press
, SP CFG is displayed.
5. Press
, press or to desired setpoint number.
6. Press
to enter setpoint settings.
7. Select the type by pressing
or to desired setting, then press to set the value. For complete list of
options see Section 3.2.13.
8. When all settings have been made, press
MENU
to return to weighing mode.
Note
Setpoints are now accessible from the front panel menu.
Display or Edit Setpoint Value
1. Press
MENU
. AUDIT is displayed.
2. Press
or until SETPTS is displayed.
3. Press
and the first available setpoint number is displayed.
4. Press
or to toggle through each setpoint that is operator accessible.
5. Press
, VALUE is displayed.
6. Press
again to display or edit the value. To edit the value:
• Press
or to increment or decrement the value of the flashing digit.
• Press
or to select the digit to edit.
• Press
TAR E
to move to the decimal point entry.
• Press
or to adjust the decimal point placement.
7. Press
TAR E
to accept the displayed value.
8. Repeat the above steps to set PREACT
, if enabled
9. When all settings have been made, press
MENU
to return to weighing mode.
Note
Setpoint Value and Preact Value may be accessible from the front panel in weigh mode.
Some indicator configurations may not allow setpoint values to
be changed through the front panel or may
require a password to display or change the setpoint value.
Turn Setpoint On or Off
To turn a setpoint off at the front panel:
1. Press
MENU
. AUDIT is displayed.
2. Press
or until SETPTS is displayed.
3. Press
and the first available setpoint number is displayed.
4. Press
or to toggle through each setpoint that is operator accessible.
5. Press
, then press or to ENABLE.
6. Press
, then press or to turn setpoint ON/OFF.
7. Press
TAR E
to accept the setting.
- 880 Performance Series 1
- Technical/Service 1
- Contents 3
- About This Manual 7
- 1.0 Introduction 7
- General Safety 8
- 1.2 Operating Modes 9
- 1.3 Front Panel Display 9
- Center of Zero LED 10
- Standstill LED 10
- 1.4 Indicator Operations 11
- 1.4.7 Print Ticket 12
- 1.4.8 Front Panel Setup 12
- 1.4.10 Setpoints 13
- Turn Setpoint On or Off 13
- 1.4.11 Set Time and Date 14
- 1.4.12 Display Accumulator 14
- 1.4.13 Clear the Accumulator 14
- 1.4.14 Display Tare 15
- 2.0 Installation 16
- 2.2 Panel Mount Installation 17
- Important 18
- J1 J2 J3 J4 J5 J6 19
- 2.4 Display Board Replacement 22
- 2.5 Cable Connections 22
- 2.6 USB Host 24
- 2.7 Ethernet Communications 24
- 2.8 CPU Board 25
- 2.10 Board Replacement 26
- 2.11 Digital I/O 28
- 2.12 Legal for Trade Sealing 28
- 2.13 Option Cards 29
- 2.14 Battery Replacement 29
- 2.15 Replacement Parts 30
- 3.1.3 User Setup Menu 33
- 0 0 0 0 0 0 34
- 3.2.1 Audit Menu 35
- 3.2.2 Setup Menu 36
- 37
- SCALE Menu 38
- 3.2.4 FORMAT Menu 40
- FORMAT Menu 41
- 3.2.5 Calibration Menu 42
- FEATUR Menu 44
- COM Menu 50
- ETHERNET Menu 52
- 3.2.11 USB Host 53
- 3.2.12 Print Format Menu 54
- Configuration 51 57
- SETPTS Menu 58
- 4.0 Calibration 63
- 4.1 Front Panel Calibration 64
- 4.1.2 Rezero 65
- 4.5 Gravity Compensation 66
- 4.6 EDP Command Calibration 67
- 4.7 Revolution 67
- Calibration 67
- 5.0 Using Revolution 68
- 5.2 Configuration 69
- 5.4 Revolution Help 70
- 6.0 EDP Commands 71
- 6.1.2 Reporting Commands 72
- Scales Menu 73
- Format Menu 73
- Calibration Menu 74
- Ports COM Menu 74
- Ports – Field Bus Menu 75
- Ports – Ethernet Menu 75
- Ports – USBCOM Menu 76
- Stream Tokens Menu 76
- Feature Menu 76
- Regulatory Menu 77
- Time and Date 77
- Passwords Menu 77
- Keypad Lock Menu 77
- Setpoints Menu 78
- Print Format Menu 80
- Analog Out Menu 80
- 6.1.5 Normal Mode Commands 81
- Digital I/O Control Menu 82
- 6.1.6 ERROR Commands Output 82
- 7.0 Print Formatting 83
- 7.2 Default Print Formats 84
- 7.3 Customizing Print Formats 85
- 7.3.3 Using Revolution 86
- 8.0 Setpoints 87
- 8.2 Batch Operations 89
- 8.3 Batching Examples 91
- Example 2 92
- 9.0 Ethernet and USB 93
- Ethernet and USB 89 95
- Using Revolution 96
- with Ethernet 96
- 9.2 USB Host 97
- 9.2.2 USB Memory storage 98
- Saving Configuration 98
- Loading Configuration 98
- 10.0 Appendix 100
- 10.3 ERROR Commands Output 101
- 10.4 Status Messages 102
- 10.6 Data Formats 103
- <STX> 104
- ONTROL-B>AXG#1<CR> 105
- 10.8.1 Toledo 8142 Indicator 108
- 10.8.2 Cardinal 738 Indicator 109
- 10.9 ASCII Character Chart 111
- 10.10 Digital Filtering 113
- (Section 4.0) 114
- 10.12 Specifications 115
- 880 Limited Warranty 116
- For More Information 117
- PN 158387 Rev C 120
Relacionado con productos y manuales para Escamas Rice-lake 880 Performance Series Indicator/Controller Techni
(4 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.142 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales