Rice-lake 880 Performance Series Indicator/Controller Techni Manual de usuario Pagina 65
- Pagina / 120
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Calibration 59
4.1.1 Five-point linearization
Five-point linearization (using the WLIN parameter) provides increased scale accuracy by calibrating the indicator
at up to five additional points between the zero and span calibrations.
Linearization is optional: if choosing not to perform linearization,
skip the WLIN parameter; if linearization values
have previously been entered, these values are reset to zero during calibration of
WZERO. To perform linearization,
follow the procedure below.
Note
The linearity points must be less than the WSPAN point.
1. With WLIN displayed, press
TAR E
to go to the first linearization point (POINT1).
2. Press
again, WGT1 is displayed.
3. Press
to edit the value:
• Press
or to select the digit.
• Press
or to increment or decrement the value.
• Press
TAR E
when the value is correct (the decimal point will be set in the following step).
• Press
or to move the decimal point position.
• Press
TAR E
when the value is correct. The indicator will display CAL1.
4. Place test weights on the scale and press
TAR E
. The indicator will display the previously captured A/D
counts for the linearization point.
5. Press
TAR E
again to calibrate. The indicator displays Calibrating, Please Wait while calibration is in
progress. When complete,
WGT1 is displayed.
6. Press
to POINT1, then press to POINT2.
7. Repeat for up to five linearization points.
To exit the linearization parameters, press to return to WLIN.
4.1.2 Rezero
The rezero function is used to remove a calibration offset when an apparatus is used to hang the test weights. If no
other apparatus was used to hang the test weights during calibration, remove the test weights and press
to return
to the
CALIBR menu.
1. With
REZERO displayed, press
TAR E
or to access the rezero function.
2. If an apparatus is used during calibration, remove it and the test
weights from the scale. The indicator will
display the AD count from the previous zero (
WZERO) calibration.
3. With all weight re
moved, press
TAR E
to rezero the scale. This function acquires a new ZERO calibration
value. The indicator displays
Calibrating, Please Wait while the zero and span calibrations are adjusted.
When complete,
LAST is displayed.
Note
For more information on LAST or TEMP see Section 4.2 or Section 4.3.
4. Press
MENU
to return to weigh mode.
- 880 Performance Series 1
- Technical/Service 1
- Contents 3
- About This Manual 7
- 1.0 Introduction 7
- General Safety 8
- 1.2 Operating Modes 9
- 1.3 Front Panel Display 9
- Center of Zero LED 10
- Standstill LED 10
- 1.4 Indicator Operations 11
- 1.4.7 Print Ticket 12
- 1.4.8 Front Panel Setup 12
- 1.4.10 Setpoints 13
- Turn Setpoint On or Off 13
- 1.4.11 Set Time and Date 14
- 1.4.12 Display Accumulator 14
- 1.4.13 Clear the Accumulator 14
- 1.4.14 Display Tare 15
- 2.0 Installation 16
- 2.2 Panel Mount Installation 17
- Important 18
- J1 J2 J3 J4 J5 J6 19
- 2.4 Display Board Replacement 22
- 2.5 Cable Connections 22
- 2.6 USB Host 24
- 2.7 Ethernet Communications 24
- 2.8 CPU Board 25
- 2.10 Board Replacement 26
- 2.11 Digital I/O 28
- 2.12 Legal for Trade Sealing 28
- 2.13 Option Cards 29
- 2.14 Battery Replacement 29
- 2.15 Replacement Parts 30
- 3.1.3 User Setup Menu 33
- 0 0 0 0 0 0 34
- 3.2.1 Audit Menu 35
- 3.2.2 Setup Menu 36
- 37
- SCALE Menu 38
- 3.2.4 FORMAT Menu 40
- FORMAT Menu 41
- 3.2.5 Calibration Menu 42
- FEATUR Menu 44
- COM Menu 50
- ETHERNET Menu 52
- 3.2.11 USB Host 53
- 3.2.12 Print Format Menu 54
- Configuration 51 57
- SETPTS Menu 58
- 4.0 Calibration 63
- 4.1 Front Panel Calibration 64
- 4.1.2 Rezero 65
- 4.5 Gravity Compensation 66
- 4.6 EDP Command Calibration 67
- 4.7 Revolution 67
- Calibration 67
- 5.0 Using Revolution 68
- 5.2 Configuration 69
- 5.4 Revolution Help 70
- 6.0 EDP Commands 71
- 6.1.2 Reporting Commands 72
- Scales Menu 73
- Format Menu 73
- Calibration Menu 74
- Ports COM Menu 74
- Ports – Field Bus Menu 75
- Ports – Ethernet Menu 75
- Ports – USBCOM Menu 76
- Stream Tokens Menu 76
- Feature Menu 76
- Regulatory Menu 77
- Time and Date 77
- Passwords Menu 77
- Keypad Lock Menu 77
- Setpoints Menu 78
- Print Format Menu 80
- Analog Out Menu 80
- 6.1.5 Normal Mode Commands 81
- Digital I/O Control Menu 82
- 6.1.6 ERROR Commands Output 82
- 7.0 Print Formatting 83
- 7.2 Default Print Formats 84
- 7.3 Customizing Print Formats 85
- 7.3.3 Using Revolution 86
- 8.0 Setpoints 87
- 8.2 Batch Operations 89
- 8.3 Batching Examples 91
- Example 2 92
- 9.0 Ethernet and USB 93
- Ethernet and USB 89 95
- Using Revolution 96
- with Ethernet 96
- 9.2 USB Host 97
- 9.2.2 USB Memory storage 98
- Saving Configuration 98
- Loading Configuration 98
- 10.0 Appendix 100
- 10.3 ERROR Commands Output 101
- 10.4 Status Messages 102
- 10.6 Data Formats 103
- <STX> 104
- ONTROL-B>AXG#1<CR> 105
- 10.8.1 Toledo 8142 Indicator 108
- 10.8.2 Cardinal 738 Indicator 109
- 10.9 ASCII Character Chart 111
- 10.10 Digital Filtering 113
- (Section 4.0) 114
- 10.12 Specifications 115
- 880 Limited Warranty 116
- For More Information 117
- PN 158387 Rev C 120
Relacionado con productos y manuales para Escamas Rice-lake 880 Performance Series Indicator/Controller Techni
(4 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.061 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales