Rice-lake 880 Performance Series Indicator/Controller Techni Manual de usuario Pagina 50
- Pagina / 120
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
44 880 Technical/Service Manual
COM Menu
Parameter Choices Description
TRIGGE COMAND Setting Trigger to command allows opration of EDP
commands and can print.
STRLFT Stream Legal for Trade data – data is updated at the configur
ed display update rate.
STRIND Stream Industrial scale data – data is upda
ted at the configured sample rate.
REMOTE Configures the port to operate as a serial scale input. See “Menu St
ructure if
TRIGGE is set to REMOTE” below. (Not available in USBCOM)
Note
When in STRLFT, STRIND and REMOTE, if the COM port is set to TYPE = RS485, the
port will not stream data, and canno
t be used in a local/remote application. See
Section 10.6.3.
BAUD 9600
19200
28800
38400
57600
115200
1200
2400
4800
Port baud rate. (Not availa
ble in USBCOM)
BITS 8NONE
7EVEN
7ODD
Port data bits and parity. (Not availa
ble in USBCOM)
STOP B 1
2
Stop Bits – selects the number of stop bits transmitted and the number of stop bits
expected to be received by the port. (Not available in USBCOM)
TERMIN CR/LF
CR
Termination – selects the ter
mination character(s) for data sent from the port.
ECHO ON
OFF
Specifies whether characters received by the port are echoed back to the sending
unit.
RESPNS ON
OFF
Response – specifies whether the port transmits replies to serial commands
EOLDLY 000000 End of Line Delay - specifies, in 0.1 second
intervals, the delay between transmitted
lines of data.
TYPE 232
485
Specifies the protocol for the COM port. (Not available in USBCOM)
ADDRES 0-255 If TYPE is 485, specifies the RS-485 address. (Not available in USBCOM)
PRNMSG OFF
ON
Print message – displays a messa
ge when a print is transmitted on this port.
SFMT <2><P><W7.>
<U><M><S>
<CR><LF>
Stream format – specifies the stream format used for streaming output of scale data
(TRIGGE=STRLFT or STRIND) or specifies the expected input for a serial scale
(TRIGGE=REMOTE).
Menu Structure if TRIGGE is set to REMOTE
TRIGGE REMOTE Configures the port to operate as a serial scale input.
BAUD 9600
19200
28800
38400
57600
115200
1200
2400
4800
Port baud rate.
Table 3-11. COM and USBCOM Menu Parameters
- 880 Performance Series 1
- Technical/Service 1
- Contents 3
- About This Manual 7
- 1.0 Introduction 7
- General Safety 8
- 1.2 Operating Modes 9
- 1.3 Front Panel Display 9
- Center of Zero LED 10
- Standstill LED 10
- 1.4 Indicator Operations 11
- 1.4.7 Print Ticket 12
- 1.4.8 Front Panel Setup 12
- 1.4.10 Setpoints 13
- Turn Setpoint On or Off 13
- 1.4.11 Set Time and Date 14
- 1.4.12 Display Accumulator 14
- 1.4.13 Clear the Accumulator 14
- 1.4.14 Display Tare 15
- 2.0 Installation 16
- 2.2 Panel Mount Installation 17
- Important 18
- J1 J2 J3 J4 J5 J6 19
- 2.4 Display Board Replacement 22
- 2.5 Cable Connections 22
- 2.6 USB Host 24
- 2.7 Ethernet Communications 24
- 2.8 CPU Board 25
- 2.10 Board Replacement 26
- 2.11 Digital I/O 28
- 2.12 Legal for Trade Sealing 28
- 2.13 Option Cards 29
- 2.14 Battery Replacement 29
- 2.15 Replacement Parts 30
- 3.1.3 User Setup Menu 33
- 0 0 0 0 0 0 34
- 3.2.1 Audit Menu 35
- 3.2.2 Setup Menu 36
- 37
- SCALE Menu 38
- 3.2.4 FORMAT Menu 40
- FORMAT Menu 41
- 3.2.5 Calibration Menu 42
- FEATUR Menu 44
- COM Menu 50
- ETHERNET Menu 52
- 3.2.11 USB Host 53
- 3.2.12 Print Format Menu 54
- Configuration 51 57
- SETPTS Menu 58
- 4.0 Calibration 63
- 4.1 Front Panel Calibration 64
- 4.1.2 Rezero 65
- 4.5 Gravity Compensation 66
- 4.6 EDP Command Calibration 67
- 4.7 Revolution 67
- Calibration 67
- 5.0 Using Revolution 68
- 5.2 Configuration 69
- 5.4 Revolution Help 70
- 6.0 EDP Commands 71
- 6.1.2 Reporting Commands 72
- Scales Menu 73
- Format Menu 73
- Calibration Menu 74
- Ports COM Menu 74
- Ports – Field Bus Menu 75
- Ports – Ethernet Menu 75
- Ports – USBCOM Menu 76
- Stream Tokens Menu 76
- Feature Menu 76
- Regulatory Menu 77
- Time and Date 77
- Passwords Menu 77
- Keypad Lock Menu 77
- Setpoints Menu 78
- Print Format Menu 80
- Analog Out Menu 80
- 6.1.5 Normal Mode Commands 81
- Digital I/O Control Menu 82
- 6.1.6 ERROR Commands Output 82
- 7.0 Print Formatting 83
- 7.2 Default Print Formats 84
- 7.3 Customizing Print Formats 85
- 7.3.3 Using Revolution 86
- 8.0 Setpoints 87
- 8.2 Batch Operations 89
- 8.3 Batching Examples 91
- Example 2 92
- 9.0 Ethernet and USB 93
- Ethernet and USB 89 95
- Using Revolution 96
- with Ethernet 96
- 9.2 USB Host 97
- 9.2.2 USB Memory storage 98
- Saving Configuration 98
- Loading Configuration 98
- 10.0 Appendix 100
- 10.3 ERROR Commands Output 101
- 10.4 Status Messages 102
- 10.6 Data Formats 103
- <STX> 104
- ONTROL-B>AXG#1<CR> 105
- 10.8.1 Toledo 8142 Indicator 108
- 10.8.2 Cardinal 738 Indicator 109
- 10.9 ASCII Character Chart 111
- 10.10 Digital Filtering 113
- (Section 4.0) 114
- 10.12 Specifications 115
- 880 Limited Warranty 116
- For More Information 117
- PN 158387 Rev C 120
Relacionado con productos y manuales para Escamas Rice-lake 880 Performance Series Indicator/Controller Techni
(4 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.064 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales