Rice-lake 880 Performance Series Indicator/Controller Techni Manual de usuario Pagina 52
- Pagina / 120
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Table 3-12. Ethernet Menu Parameters
ETHERNET Menu
Parameter Choices Description
DHCP ON
OFF
Enables (ON) or disables (OFF) Dynami
c Host Configuration Protocal.
IPADRS 000.000.000.000
Valid IP Address
Configures the IP address for this device.
NETMSK 000.000.000.000
Valid Net Mast
Specifies the subnet mask.
DFTGWY 000.000.000.000
Valid IP Address
Default Gateway.
DNSPRI 000.000.000.000
Valid IP Address
IP address for the primary DNS server.
DNSSEC 000.000.000.000
Valid IP Address
IP address for the seco
ndary DNS server.
SERVER See SERVER Sublevel below
CLIENT See CLIENT Sublevel below
MAC 00.00.00.00.00.00
The MAC address for this device, read only.
SERVER/CLIENT Sublevel
RMOTIP 000.000.000.000
Valid IP Address
Remote IP address – IP address of the remote unit the 880 will connect to.
Client level only.
RMOTPT 1
1-65535
Remote port – TCP port number on the remote unit the 880 will connect to.
Client level only.
PORT 10001
1-65535
The TCP port number of the 880 server. Server level
only.
TRIGGE COMAND
STRIND
STRLFT
Selects the operation of the port.
•COMAND – allows operation of EDP commands and will print
•STRLFT – stream legal for trade scale data – data is transmitted at the configured
display update rate. Will also accept EDP commands.
•STRIND – stream industrial scale data – data
is transmitted at the configured A/D
sample rate. Will also accept EDP commands.
TERMIN CR/LF
CR
Termination. Selects the termination character(s) for data sent from the port.
EOLDLY 0
0-255
Port end-of-line delay, 0.1 second intervals.
TIMOUT 0
0-65535
Timeout – inactivity disconnect timeout. A connection (eithe
r client or server) is
dropped if there is no activity before the timeout expires. Time is in seconds. A
timeout value of 0 disables the inactivity disconnect.
SFMT <2><P><W7.>
<U><M><S>
<CR><LF>
Stream format – specifies the stream format
used for streaming output of scale data
(TRIGGE=STRLFT or STRIND). Alpha/numeric maximum length 200 characters.
ECHO OFF
ON
Specifies whether characters received by the port are echoed back to the sending unit.
RESPNS ON
OFF
Response – specifies whether the port transmits
replies to serial commands.
Note
If an external device (such as a printer) that may transmit unexpected
data (such as a paper low message) is connected to the indicator the
respo
nse parameter should be set to OFF to prevent a reply from the
indicator from confusing the external device.
46 880 Technical/Service Manual
- 880 Performance Series 1
- Technical/Service 1
- Contents 3
- About This Manual 7
- 1.0 Introduction 7
- General Safety 8
- 1.2 Operating Modes 9
- 1.3 Front Panel Display 9
- Center of Zero LED 10
- Standstill LED 10
- 1.4 Indicator Operations 11
- 1.4.7 Print Ticket 12
- 1.4.8 Front Panel Setup 12
- 1.4.10 Setpoints 13
- Turn Setpoint On or Off 13
- 1.4.11 Set Time and Date 14
- 1.4.12 Display Accumulator 14
- 1.4.13 Clear the Accumulator 14
- 1.4.14 Display Tare 15
- 2.0 Installation 16
- 2.2 Panel Mount Installation 17
- Important 18
- J1 J2 J3 J4 J5 J6 19
- 2.4 Display Board Replacement 22
- 2.5 Cable Connections 22
- 2.6 USB Host 24
- 2.7 Ethernet Communications 24
- 2.8 CPU Board 25
- 2.10 Board Replacement 26
- 2.11 Digital I/O 28
- 2.12 Legal for Trade Sealing 28
- 2.13 Option Cards 29
- 2.14 Battery Replacement 29
- 2.15 Replacement Parts 30
- 3.1.3 User Setup Menu 33
- 0 0 0 0 0 0 34
- 3.2.1 Audit Menu 35
- 3.2.2 Setup Menu 36
- 37
- SCALE Menu 38
- 3.2.4 FORMAT Menu 40
- FORMAT Menu 41
- 3.2.5 Calibration Menu 42
- FEATUR Menu 44
- COM Menu 50
- ETHERNET Menu 52
- 3.2.11 USB Host 53
- 3.2.12 Print Format Menu 54
- Configuration 51 57
- SETPTS Menu 58
- 4.0 Calibration 63
- 4.1 Front Panel Calibration 64
- 4.1.2 Rezero 65
- 4.5 Gravity Compensation 66
- 4.6 EDP Command Calibration 67
- 4.7 Revolution 67
- Calibration 67
- 5.0 Using Revolution 68
- 5.2 Configuration 69
- 5.4 Revolution Help 70
- 6.0 EDP Commands 71
- 6.1.2 Reporting Commands 72
- Scales Menu 73
- Format Menu 73
- Calibration Menu 74
- Ports COM Menu 74
- Ports – Field Bus Menu 75
- Ports – Ethernet Menu 75
- Ports – USBCOM Menu 76
- Stream Tokens Menu 76
- Feature Menu 76
- Regulatory Menu 77
- Time and Date 77
- Passwords Menu 77
- Keypad Lock Menu 77
- Setpoints Menu 78
- Print Format Menu 80
- Analog Out Menu 80
- 6.1.5 Normal Mode Commands 81
- Digital I/O Control Menu 82
- 6.1.6 ERROR Commands Output 82
- 7.0 Print Formatting 83
- 7.2 Default Print Formats 84
- 7.3 Customizing Print Formats 85
- 7.3.3 Using Revolution 86
- 8.0 Setpoints 87
- 8.2 Batch Operations 89
- 8.3 Batching Examples 91
- Example 2 92
- 9.0 Ethernet and USB 93
- Ethernet and USB 89 95
- Using Revolution 96
- with Ethernet 96
- 9.2 USB Host 97
- 9.2.2 USB Memory storage 98
- Saving Configuration 98
- Loading Configuration 98
- 10.0 Appendix 100
- 10.3 ERROR Commands Output 101
- 10.4 Status Messages 102
- 10.6 Data Formats 103
- <STX> 104
- ONTROL-B>AXG#1<CR> 105
- 10.8.1 Toledo 8142 Indicator 108
- 10.8.2 Cardinal 738 Indicator 109
- 10.9 ASCII Character Chart 111
- 10.10 Digital Filtering 113
- (Section 4.0) 114
- 10.12 Specifications 115
- 880 Limited Warranty 116
- For More Information 117
- PN 158387 Rev C 120
Relacionado con productos y manuales para Escamas Rice-lake 880 Performance Series Indicator/Controller Techni
(4 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.080 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales