Rice-lake 880 Performance Series Indicator/Controller Techni Manual de usuario Pagina 29
- Pagina / 120
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installation 23
4. Insert the other screw into the hole for the setup switch access.
Fillister Head Screw
Fillister Head Screw
5. Install the wire by threading through the two fillister head screws and the hole in the top of the load cell
sealing clip. Seal the wire to secure.
Sealing Wire
Figure 2-18. Install Sealing Wire
2.13 Option Cards
Connector J8 is reserved for option cards. Table 2-5 lists the options available for the 880 Indicator. Each kit
includes instructions for installing and setti
ng up the option.
Table 2-5. Available Option Cards
Option Addendum Part Number
Analog Output Card 131601
Relay Board 131602
EtherNet/IP 156554
DeviceNet 156558
Profibus DP 156556
Modbus TCP 156557
ProfiNet 156555
2.14 Battery Replacement
When battery voltage gets low, the indicator display shows low bat. Replace the battery when this warning is
displayed. The battery should last about seven years.
• Use the Revolution configuration uti
lity or EDP commands (see Section 6.1 on page 65) to store a copy of the
indicator configuration on a PC before
attempting battery replacement. If any data is lost, the indicator
configuration can be restored from the PC.
WARNING
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of unused batteries according to the manufacturer’s instructions.
The battery should be considered bad and discarded at 2.9V.
- 880 Performance Series 1
- Technical/Service 1
- Contents 3
- About This Manual 7
- 1.0 Introduction 7
- General Safety 8
- 1.2 Operating Modes 9
- 1.3 Front Panel Display 9
- Center of Zero LED 10
- Standstill LED 10
- 1.4 Indicator Operations 11
- 1.4.7 Print Ticket 12
- 1.4.8 Front Panel Setup 12
- 1.4.10 Setpoints 13
- Turn Setpoint On or Off 13
- 1.4.11 Set Time and Date 14
- 1.4.12 Display Accumulator 14
- 1.4.13 Clear the Accumulator 14
- 1.4.14 Display Tare 15
- 2.0 Installation 16
- 2.2 Panel Mount Installation 17
- Important 18
- J1 J2 J3 J4 J5 J6 19
- 2.4 Display Board Replacement 22
- 2.5 Cable Connections 22
- 2.6 USB Host 24
- 2.7 Ethernet Communications 24
- 2.8 CPU Board 25
- 2.10 Board Replacement 26
- 2.11 Digital I/O 28
- 2.12 Legal for Trade Sealing 28
- 2.13 Option Cards 29
- 2.14 Battery Replacement 29
- 2.15 Replacement Parts 30
- 3.1.3 User Setup Menu 33
- 0 0 0 0 0 0 34
- 3.2.1 Audit Menu 35
- 3.2.2 Setup Menu 36
- 37
- SCALE Menu 38
- 3.2.4 FORMAT Menu 40
- FORMAT Menu 41
- 3.2.5 Calibration Menu 42
- FEATUR Menu 44
- COM Menu 50
- ETHERNET Menu 52
- 3.2.11 USB Host 53
- 3.2.12 Print Format Menu 54
- Configuration 51 57
- SETPTS Menu 58
- 4.0 Calibration 63
- 4.1 Front Panel Calibration 64
- 4.1.2 Rezero 65
- 4.5 Gravity Compensation 66
- 4.6 EDP Command Calibration 67
- 4.7 Revolution 67
- Calibration 67
- 5.0 Using Revolution 68
- 5.2 Configuration 69
- 5.4 Revolution Help 70
- 6.0 EDP Commands 71
- 6.1.2 Reporting Commands 72
- Scales Menu 73
- Format Menu 73
- Calibration Menu 74
- Ports COM Menu 74
- Ports – Field Bus Menu 75
- Ports – Ethernet Menu 75
- Ports – USBCOM Menu 76
- Stream Tokens Menu 76
- Feature Menu 76
- Regulatory Menu 77
- Time and Date 77
- Passwords Menu 77
- Keypad Lock Menu 77
- Setpoints Menu 78
- Print Format Menu 80
- Analog Out Menu 80
- 6.1.5 Normal Mode Commands 81
- Digital I/O Control Menu 82
- 6.1.6 ERROR Commands Output 82
- 7.0 Print Formatting 83
- 7.2 Default Print Formats 84
- 7.3 Customizing Print Formats 85
- 7.3.3 Using Revolution 86
- 8.0 Setpoints 87
- 8.2 Batch Operations 89
- 8.3 Batching Examples 91
- Example 2 92
- 9.0 Ethernet and USB 93
- Ethernet and USB 89 95
- Using Revolution 96
- with Ethernet 96
- 9.2 USB Host 97
- 9.2.2 USB Memory storage 98
- Saving Configuration 98
- Loading Configuration 98
- 10.0 Appendix 100
- 10.3 ERROR Commands Output 101
- 10.4 Status Messages 102
- 10.6 Data Formats 103
- <STX> 104
- ONTROL-B>AXG#1<CR> 105
- 10.8.1 Toledo 8142 Indicator 108
- 10.8.2 Cardinal 738 Indicator 109
- 10.9 ASCII Character Chart 111
- 10.10 Digital Filtering 113
- (Section 4.0) 114
- 10.12 Specifications 115
- 880 Limited Warranty 116
- For More Information 117
- PN 158387 Rev C 120
Relacionado con productos y manuales para Escamas Rice-lake 880 Performance Series Indicator/Controller Techni
(4 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.097 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales