Rice-lake 880 Performance Series Indicator/Controller Techni Manual de usuario Pagina 114
- Pagina / 120
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
108 880 Technical/Service Manual
10.11 Analog Output Calibration
See Section 3.0, Table 3-17 for ANALOG OUTPUT parameters.
The following calibration procedure requires
a multimeter to measure voltage or current output from the analog
output module. If the option is not already installed, install it in according to the instructions included with the
option.
Note
The analog output must be calibrated after the indicator itself has been configured (Section 3.0) and calibrated
(Section 4.0).
1. Enter setup mode and go to the ALGOUT menu (see Figure 3-23):
• Set OUTPUT as desired for 0-10V, 0-20mA, or 4-20mA output.
• Set MIN to lowest weight value to
be tracked by the analog output
• Set MAX to highest weight value to
be tracked by the analog output
2. Connect multimeter to connector J1 on the
analog output board:
• For voltage output, connect voltmeter
leads to pins 3 and 4 (-V, +V)
• For current output, connect ammeter leads to
pins 1 and 2 (-mA, +mA)
3. Adjust zero calibration:
• Scroll to the TWZERO parameter.
• Press
, 000000 will display
• Check voltage or current reading on multimeter
.
• Set the parameter to match t
he reading from the multimeter.
• Press
or to select the digit.
• Press
or to increment or decrement the value.
• Press
TAR E
to move to the decimal point entry.
• Press
or to adjust the decimal point placement.
• Press
TAR E
to accept the displayed value.
4. Adjust span calibration:
• Scroll to the TWSPAN parameter.
• Press
, 000000 will display.
• Set the parameter to match t
he reading from the multimeter.
• Press
or to select the digit.
• Press
or to increment or decrement the value.
• Press
TAR E
to move to the decimal point entry.
• Press
or to adjust the decimal point placement.
• Press
TAR E
to accept the displayed value.
5. Verify calibration:
• Return to the TWZERO/TWSPAN parameter and verify that
the calibration has not drifted.
• Repeat calibration if needed.
6. Return to normal mode. Analog output function can be verified using test weights.
- 880 Performance Series 1
- Technical/Service 1
- Contents 3
- About This Manual 7
- 1.0 Introduction 7
- General Safety 8
- 1.2 Operating Modes 9
- 1.3 Front Panel Display 9
- Center of Zero LED 10
- Standstill LED 10
- 1.4 Indicator Operations 11
- 1.4.7 Print Ticket 12
- 1.4.8 Front Panel Setup 12
- 1.4.10 Setpoints 13
- Turn Setpoint On or Off 13
- 1.4.11 Set Time and Date 14
- 1.4.12 Display Accumulator 14
- 1.4.13 Clear the Accumulator 14
- 1.4.14 Display Tare 15
- 2.0 Installation 16
- 2.2 Panel Mount Installation 17
- Important 18
- J1 J2 J3 J4 J5 J6 19
- 2.4 Display Board Replacement 22
- 2.5 Cable Connections 22
- 2.6 USB Host 24
- 2.7 Ethernet Communications 24
- 2.8 CPU Board 25
- 2.10 Board Replacement 26
- 2.11 Digital I/O 28
- 2.12 Legal for Trade Sealing 28
- 2.13 Option Cards 29
- 2.14 Battery Replacement 29
- 2.15 Replacement Parts 30
- 3.1.3 User Setup Menu 33
- 0 0 0 0 0 0 34
- 3.2.1 Audit Menu 35
- 3.2.2 Setup Menu 36
- 37
- SCALE Menu 38
- 3.2.4 FORMAT Menu 40
- FORMAT Menu 41
- 3.2.5 Calibration Menu 42
- FEATUR Menu 44
- COM Menu 50
- ETHERNET Menu 52
- 3.2.11 USB Host 53
- 3.2.12 Print Format Menu 54
- Configuration 51 57
- SETPTS Menu 58
- 4.0 Calibration 63
- 4.1 Front Panel Calibration 64
- 4.1.2 Rezero 65
- 4.5 Gravity Compensation 66
- 4.6 EDP Command Calibration 67
- 4.7 Revolution 67
- Calibration 67
- 5.0 Using Revolution 68
- 5.2 Configuration 69
- 5.4 Revolution Help 70
- 6.0 EDP Commands 71
- 6.1.2 Reporting Commands 72
- Scales Menu 73
- Format Menu 73
- Calibration Menu 74
- Ports COM Menu 74
- Ports – Field Bus Menu 75
- Ports – Ethernet Menu 75
- Ports – USBCOM Menu 76
- Stream Tokens Menu 76
- Feature Menu 76
- Regulatory Menu 77
- Time and Date 77
- Passwords Menu 77
- Keypad Lock Menu 77
- Setpoints Menu 78
- Print Format Menu 80
- Analog Out Menu 80
- 6.1.5 Normal Mode Commands 81
- Digital I/O Control Menu 82
- 6.1.6 ERROR Commands Output 82
- 7.0 Print Formatting 83
- 7.2 Default Print Formats 84
- 7.3 Customizing Print Formats 85
- 7.3.3 Using Revolution 86
- 8.0 Setpoints 87
- 8.2 Batch Operations 89
- 8.3 Batching Examples 91
- Example 2 92
- 9.0 Ethernet and USB 93
- Ethernet and USB 89 95
- Using Revolution 96
- with Ethernet 96
- 9.2 USB Host 97
- 9.2.2 USB Memory storage 98
- Saving Configuration 98
- Loading Configuration 98
- 10.0 Appendix 100
- 10.3 ERROR Commands Output 101
- 10.4 Status Messages 102
- 10.6 Data Formats 103
- <STX> 104
- ONTROL-B>AXG#1<CR> 105
- 10.8.1 Toledo 8142 Indicator 108
- 10.8.2 Cardinal 738 Indicator 109
- 10.9 ASCII Character Chart 111
- 10.10 Digital Filtering 113
- (Section 4.0) 114
- 10.12 Specifications 115
- 880 Limited Warranty 116
- For More Information 117
- PN 158387 Rev C 120
Relacionado con productos y manuales para Escamas Rice-lake 880 Performance Series Indicator/Controller Techni
(4 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales